Skip to content

Serving all 50 states + Washington, DC

Keystream Plumbing logoKeystreamPlumbing

Pipes and fixtures

Faucet and fixture repair

Dripping faucets and shower valves are usually fixed by replacing a cartridge, washer or seat. New faucets, sinks, shower valves and garbage disposals are installed with new supply lines and shutoffs as needed.

  • Independent licensed local plumbers
  • The plumber gives you a price before work starts
  • Free referral, no obligation
Stainless steel faucet on a white bathroom sink

A faucet that drips from the spout needs internal parts, a cartridge in most modern faucets or a washer and seat in older compression styles. Water leaking around the handle points to O-rings. Shower valves work the same way, but they sit inside the wall, so repairs go through the trim plate; a plumber will match the brand's cartridge where possible.

When replacing a fixture, it's the right time to replace old supply lines and corroded shutoff valves. Braided stainless supply lines are inexpensive insurance against a burst rubber hose. In hard water areas, mineral buildup shortens cartridge life, so expect to replace them more often.

Faucet and Fixture Repair at a glance

Service
Faucet and Fixture Repair
Category
Pipes and fixtures
Availability
Scheduled and same-day visits, depending on local availability
Service area
Requests accepted from all 50 states and Washington, DC; availability depends on the pros near your ZIP code
Also called
faucet replacement, shower valve repair, fixture installation
Common fix
Cartridge or washer replacement
Cost
Quoted on site by the pro before work starts; see cost factors below

Specific faucet repair jobs

Narrower jobs within this service, each with its own guide.

Signs you need faucet and fixture repair

  • A faucet or showerhead that drips after it's turned off
  • Water leaking around a handle or under the sink
  • Low flow from one fixture only
  • A shower that runs too hot or cold
  • Stiff or loose handles

What the pro does, step by step

  1. 1

    Identify the fixture

    The plumber identifies brand and model to match cartridges and parts.

  2. 2

    Repair

    Cartridges, washers, O-rings and aerators are replaced and mineral buildup cleaned.

  3. 3

    Or install new

    New faucets, valves and fixtures are installed with new supply lines and shutoffs.

  4. 4

    Test

    Everything is checked for leaks, temperature and flow.

What affects the cost of faucet and fixture repair

Prices vary by market and job. The pro gives you a price before starting; these factors drive it.

  • Brand and part availability
  • In-wall shower valve versus sink faucet
  • New shutoff valves or supply lines
  • Fixture supplied by you or the plumber
  • Wall or countertop modifications

What you can safely do, and when to stop

Safe to do yourself

  • Clean or replace a clogged aerator
  • Replace a showerhead
  • Swap old rubber supply hoses for braided lines
  • Tighten a loose handle screw

Stop and call a pro

  • Shutoff valves won't close or leak when turned
  • In-wall shower valve replacement
  • Water inside the wall or cabinet base
  • Corroded or frozen fittings

Faucet and Fixture Repair FAQ

Is it worth fixing a dripping faucet?

Yes. A steady drip can waste thousands of gallons a year, and the repair is usually a single cartridge or washer.

Why is only one faucet low on pressure?

A clogged aerator or cartridge is the usual cause. If every fixture is low, the issue is in the supply lines or the pressure regulator.

Can a plumber install a faucet I bought?

Most plumbers will install customer-supplied fixtures; some limit the warranty to their labor.

How often do faucet cartridges need replacing?

Often every 5 to 10 years, sooner in hard water areas.

Should I repair or replace a leaking faucet?

Repair it if the body is sound and the cartridge, seats or washers are available. Replace it when the finish or body is corroded, the same leak keeps returning or parts for the model are no longer made.

How long does a faucet repair or replacement take?

A cartridge or washer replacement usually takes under an hour. Replacing a faucet takes one to two hours, longer when old supply lines, shutoff valves or a corroded mounting nut have to be dealt with.

Why does my faucet leak at the base or under the sink?

A leak around the base of the spout usually means worn O-rings. Water under the sink more often comes from the supply connections, the shutoff valves or the sprayer hose, so dry everything and watch where the first drop forms.

Why does my shower go hot or cold when someone flushes?

The shower valve is not balancing pressure. A worn pressure-balancing cartridge, or an older valve without one, lets the temperature swing when cold water is drawn elsewhere. Replacing the cartridge or the valve fixes it.

What should I do before the plumber arrives for a fixture repair?

Close the stop valves under the sink or the main if the leak is steady, clear out the cabinet and note the brand and model if you can find it. Knowing the brand lets the plumber bring the right cartridge.

Sources

Faucet and Fixture Repair by location

Local water, housing and permit rules change what this job involves. Find local conditions for your area:

Somewhere else? Browse plumbing conditions in all 50 states.

Get faucet and fixture repair help now

Call (833) 520-4758 to reach an available local pro.

Call now(833) 520-4758